Tube Amp Forum: The Ultimate Tone
10W amp - Printable Version

+- Tube Amp Forum: The Ultimate Tone (https://theultimatetone.com)
+-- Forum: Tube Amp Community (Hi-fi too!) (https://theultimatetone.com/forum-1.html)
+--- Forum: Personal Projects (https://theultimatetone.com/forum-6.html)
+--- Thread: 10W amp (/thread-85.html)

10W amp - jmcd - 01-27-2019

Hi Gang,

My latest build uses KOC's 10W power transformer (by SumR), KOC's 3H choke (by Hammond), a power-supply PCB (my own design, but borrowed KOC's bias supply), and a turret board for the pre- and power amp. It's got quite a bit of gain on tap. Vintage and modern modes accessible via the front-panel Era switch.

[Image: RD9gikNh.jpg]

[Image: JFKxoVIh.jpg]

RE: 10W amp - jmcd - 01-27-2019

Question: How much residual AC ripple is acceptable for the negative bias supply?

RE: 10W amp - K O'Connor - 01-27-2019

Hi jmcd

You say my bias supply without a reference to a schematic?

The ones that are actually mine have large filters and extremely low hum as a result, and are tied to the correct points to follow galactic Ground principles.

Every supply node should have the lowest ripple possible, within reason of complexity, cost and circuit context. For an SE amp, cost or complexity must be spent to assure a quiet output, where push-pull has inherent power supply noise rejection when balance  and thus the latter can have a noisier PSU but be quieter overall than SE.

Have fun

RE: 10W amp - jmcd - 01-27-2019

(01-27-2019, 11:36 PM)K O\Connor Wrote: Hi jmcd

You say my bias supply without a reference to a schematic?

The ones that are actually mine have large filters and extremely low hum as a result, and are tied to the correct points to follow galactic Ground principles.

Every supply node should have the lowest ripple possible, within reason of complexity, cost and circuit context. For an SE amp, cost or complexity must be spent to assure a quiet output, where push-pull has inherent power supply noise rejection when balance  and thus the latter can have a noisier PSU but be quieter overall than SE.

Have fun

I didn't want to post a schematic of your stuff Smile

The negative bias supply in this amp is similar to the one on your 10W power supply PCB. Schematic is probably identical.

RE: 10W amp - K O'Connor - 01-28-2019

Hi jmcd

Note that earlier the Cs were small and now they are large; should be 100uF in all positions.

Have fun

RE: 10W amp - makinrose - 01-28-2019

Looks interesting! What is the pre-amp design?

RE: 10W amp - jmcd - 01-28-2019

(01-28-2019, 02:30 AM)K O\Connor Wrote: Hi jmcd

Note that earlier the Cs were small and now they are large; should be 100uF in all positions.

Have fun

Fantastico! Time for another Digikey order Smile

(01-28-2019, 01:11 PM)makinrose Wrote: Looks interesting!  What is the pre-amp design?

Three gain stages, with EQ after the last gain stage. A bit more gain on tap than in a JCM800; more modern feel with 'era' switch set to 'modern'.

RE: 10W amp - jmcd - 02-08-2019

Another novice-level question:

I purchased a LP-style guitar with some soft of Gibson pickups. The guitar sounds great, but there is more squeal through my little high-gain amp.

What causes one humbucker guitar to squeal more than another? And is there anything to be done to reduce the squeal (besides turning down Smile)

[Image: TfK8JB0h.jpg]

RE: 10W amp - K O'Connor - 02-08-2019

Hi jmcd

Guitar pickups have the usual parasitic elements of inductance and capacitance and these vary with the design and the manufacturing consistency. The latter can manifest itself with how the wire is wrapped - is it neat, tight layers, or does the bulk of turns simply fill the space? neat winding leads to both pickups sounding the same and sounding the same from one guitar to the next. Loose windings may be "vintage" in a way, although I doubt any manufactured pickup was made that way, and definitely gives uniqueness to each pickup and thus to each guitar.

In any case, it seems like a damping resistor would be the simplest fix to employ; just place this across the output of the offending pickup ahead of the volume and tone controls. You could get fancy and use a cap in series with a resistor, but that would be difficult to tune without using a scope. As soon as I write that, I realise doing it by ear is about the same as adding the R and tweaking that by ear.

RE: 10W amp - makinrose - 02-09-2019

JMCD,

If it has Burstbuckers that's would also explain your troubles. Those pickups are unpotted and purposely wound with uneven coils. I had some at one point and they squealed with high volume and high gain. I liked using them to get feedback at low volumes for recording but eventually tired dealing with the noise.

Most of the of Gibson pickups are well potted and are supposed to have even windings...I'm interested to see how Kevin's suggestion works for you.

RE: 10W amp - sinusoids - 02-20-2019

How did you make the front panel? Looks great.

RE: 10W amp - jmcd - 02-24-2019

Thanks! I get my panels from Mason at TMI Amplification. He's on a tube-amp-builders group on FB.

RE: 10W amp - jmcd - 03-26-2019

Hi All,

I'm starting to source my aluminum chassis and cabinets locally. My first locally built chassis is still in the works, but here are a few photos of the head cab that we built for this 10W amp. V2 Badge to be added later...

Purple plain jane:
[Image: a9KfXz6h.jpg]

With ventilated front grill:
[Image: O8SzlmUh.jpg]


Simple rear panel to protect tubes and allow for reasonable air flow:
[Image: VHXpFwTh.jpg]

RE: 10W amp - enriqueperez - 01-31-2020

Good Post!